TRAINING PRACTICAL INTERNAL CORROSION CONTROL AND MONITORING IN OIL & GAS OPERATIONS
Training Praktis Pengendalian Korosi Internasional Dan Pemantauan Dalam Operasi Minyak & Gas
Training Catastrophic Effects Of Corrosive Agents And Microorganism In The Gas
training practical internal corrosion control and monitoring in oil & gas operations
Internal Corrosion Problems in Gas, Oil and Produced Water Pipeline and Equipment
* Piping and Pipeline Leakage due to Pitting Corrosion and Microbiological Induced Corrosion
* Severe Pipe Wall Thickness Reduction and Short Remaining Service Life caused by Sour Corrosion
* Pipe Wall, Rotating Parts and Equipment Cracking due to Chloride and Sulfide in the Fluids
* Internal Corrosion of Pipeline and Equipment due to Water in Oil and Oil in Water Emulsions
* Internal Corrosion due to Multi Phase Flow in the Pipeline
* Severe Corrosion Rate caused by CO2 and Hydrate in the Gas Lines, CO2/H2S Removal Unit and Glycol Dehydration Unit
* Internal Corrosion in the Water Lines due to Dissolved Oxygen, Mud and Sludge
* Malfunction of Pump, Compressor, Valves and Equipment due to Under-Deposit Corrosion, Under-Film Corrosion and Fouling
The Nature, Mechanism and Characteristics of Internal Corrosion and the Control Methods
* Anodic-Cathodic Reactions, Electrical Properties and Characteristics of Corrosion Cells
* Physical & Metallurgical Conditions of Metals and Chemical Composition that Promote Corrosion
* Destructive and Catastrophic Effects of Corrosive Agents and Microorganism in the Gas, Oil and Produced Water Fluids
* The Role and Mechanism of O2, CO2, H2S, Dissolved Salts and Microorganism in Internal Corrosion
* The Role of Oilfield Bacteria and the Mechanism of MIC
* Characteristics and Detection of Internal Corrosion in the Pipeline and Surface Equipment
* Removal of Dissolved Corrosive Agents and Non-Hydrocarbon Gases in the Gas, Oil and Produced Water Fluids
* Internal Corrosion Control with On-line Chemical Inhibitors Injection, Surface Barriers and Scavengers
Internal Corrosion Detection and Monitoring Techniques, Devices and Analysis
* Visual Inspection and Early Detection Techniques & Devices for Monitoring Fluid Corrosiveness and Tests for Identifying Corrosion products
* The Important of Internal Corrosion Rate Monitoring Before and After Chemical Injection and Treatment
* NACE Standard Method for Preparation, Installation, Laboratory Analysis and Interpretation of Results of Internal Corrosion Monitoring
* Access Fittings, Retrievers, Corrosion Coupons, Scale Coupons, Corrosion Probes, Holders, Injection & Sampling Devices and Instrument for On-line Internal Corrosion Monitoring
* The Use of Nipple or Spool, Hydrogen Probe and Galvanic Probe
* NACE Standard Method for Testing and Analysis of Bacterial Activity and Microbiological Induced Corrosion
* Iron Content Analysis of Produced Water and the COPRA Correlation
* Down-hole Tubing or Casing Calipers, Ultrasonic Wall Thickness Testers and Radiography
Internal Corrosion Control with Chemical Inhibitor Injection, Passive Film Formation and Biocides
* Nature & Classification of Inhibitors and Effect of Ionic Character on
* Inhibiting Ability
* Formulations of Oilfield Inhibitors and the use of Water Soluble Inhibitors, Volatile Inhibitors and Acid Inhibitors
* Typical Corrosion Inhibitors, Scavengers & Biocides for Oil & Gas Field
* Guidelines of Inhibitor and Biocide Applications and the Chemical Injection Equipment for Pipeline and Surface Facility
* Inhibitor and Biocide Batch Treatment Using Pigs, Chemical Dosage and the Pigging Operations
* Surfactant and Cleaners for Solving Fouling Problem in the Equipment and Systems
* Cationic & Mixed Charge Organic Inhibitors for Hydrocarbon and Oxygen Corrosion Inhibitors for Produced Water
* Testing and Evaluation of Inhibitor and Biocide Effectiveness
* Safety Precaution in Working with Inhibitors and Biocides
Internal Corrosion Control as a Key Factor to Pipeline Integrity Management
* Hazard Assessment and Risk Based Inspection for the Pipeline and Equipment Maintenance Program
* Pipeline Internal Damage Record and Wall Thickness Monitoring
* Pigging for Water and Deposit Removal from the Pipeline System
* Controlling of Flow Stability and Corrosion Rate to a Safe Level
* Estimating Present Pipeline Remaining Service Life
* Evaluation of Present Condition and Comparison with Initial Pipeline Design Baseline
* Evaluation and Controlling of Chemical Inhibitor and Biocide Injection by using Corrosion Rate Monitoring Data.
* Evaluation of Pipeline and Equipment Damage in accordance with Root Cause Failure Analysis
* Development of Specific Pipeline Integrity Management System by using Internal Corrosion Rate Monitoring Data
Course Leader: Hilman Ahmad
training practical internal corrosion control and monitoring in oil & gas operations
This specially designed course will be conducted by Hilman Ahmad & Associates, an Independent Consultant in industrial oil and gas, member of the Society of Indonesian Petroleum Engineers, who manage the Professional Industrial Oil & Gas Education Center, and has been practicing production operation & safety and corrosion control engineering in Indonesia for more than twenty-five years. He post-graduated from Tokyo Institute of Technology (sponsored by UNESCO) in 1977. He joined in-field-practice program at Nippon Kokan Steel Company & Research Center Kawasaki, Japan for production facility design & construction and corrosion prevention & control in 1983, and collaborated with Cormon Industrial Research Center Brighton UK for on-line corrosion monitoring development in 2000. He has been delivering training course in production operation, maintenance & safety and corrosion control for personnel from Oil & Gas Company and Petrochemical Industry since 1979.
Karena kompleksnya pelatihan ini, maka dibutuhkan pendalaman yang lebih komprehensif melalui sebuah training. Dan menjadi sebuah kebutuhan akan training provider yang berpengalaman di bidangnya agar tidak membuat peserta menjadi cepat bosan dan jenuh dalam mendalami bidang teknik ini.
JADWAL PELATIHAN 2024
JADWAL PELATIHAN 2025
- BATCH 1 : 13-14 Januari 2025
- BATCH 2 : 10-11 Februari 2025
- BATCH 3 : 10-11 Maret 2025
- BATCH 4 : 14-15 April 2025
- BATCH 5 : 15-16 Mei 2025
- BATCH 6 : 12-13 Juni 2025
- BATCH 7 : 10-11 Juli 2025
- BATCH 8 : 18-19 Agustus 2025
- BATCH 9 : 17-18 September 2025
- BATCH 10 : 16-17 Oktober 2025
- BATCH 11 : 13-14 November 2025
- BATCH 12 : 15-16 Desember 2025
Jadwal tersebut dapat disesuaikan dengan kebutuhan calon peserta
Lokasi training practical internal corrosion control and monitoring in oil & gas operations :
- TEMPAT PELAKSANAAN PELATIHAN
- REGULER TRAINING
- YOGYAKARTA, Hotel Dafam Malioboro
- JAKARTA, Hotel Amaris Tendean
- BANDUNG, Hotel Golden Flower
- SURABAYA
- BALI, Hotel Ibis Kuta
- LOMBOK – NTB
- ONLINE TRAINING VIA ZOOM
- IN HOUSE TRAINING
Note :
Waktu dan tempat pelaksanaan pelatihan bisa kami sesuaikan dengan kebutuhan peserta.
Investasi Pelatihan Tahun 2021-2024 ini :
Investasi pelatihan tersebut menyesuaikan dengan jumlah peserta (on call). *Please feel free to contact us.
Apabila perusahaan membutuhkan paket in house training, anggaran investasi pelatihan dapat menyesuaikan dengan anggaran perusahaan.
- REGULER TRAINING
Fasilitas
- FREE Airport pickup service (Gratis Antar jemput Hotel/Bandara)
- FREE Akomodasi Peserta ke tempat pelatihan bagi peserta
- Module / Handout
- FREE Flashdisk
- FREE Bag or bagpackers (Tas Training)
- Training Kit (Dokumentasi photo, Blocknote, ATK, etc)
- 2xCoffe Break & 1 Lunch, Dinner
- FREE Souvenir Exclusive
